Mercedes C-Class

W203 since 2000 of release

Repair and operation of the car



Mercedes-Benz
+ Mercedes-Benz cars of class C (W-203)
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   - Leaving and external equipment of a body
      General information and security measures when carrying out body works
      Cleaning and leaving
      Repair of insignificant damages of body panels
      Repair of considerable damages of a body
      Damages of a windshield as a result of hit of stones
      Replacement of brushes of screen wipers
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of back glass
      Removal and installation of the lever of a screen wiper of a windshield
      Removal and installation of the lever of a back screen wiper
      Removal and installation of a catchment basin
      Removal and installation of a cowl
      Removal and installation of facing of a cowl
      Adjustment of a cowl
      Removal and installation of the lock of a cowl
      Drive cable detachment from the cowl lock
      Removal and installation of a lattice of a spoiler
      Removal and installation of a bumper
      Removal and installation of a rear bumper
      Removal and installation of a forward wing
      Removal and installation of a protective level on a wing
      Removal and installation of a protective level on a bumper
      Removal and installation of a protective level on a door
      Removal and installation of a forward loker covered
      Removal and installation of a back part of a loker of a wing
      Removal and installation of a forward door
      Adjustment of a door
      Removal and installation of forward facing of a door
      Removal and installation of a triangular slip
      Removal and installation of the external handle of a door
      Removal and installation of facing of an external rear-view mirror
      Removal and installation of an external mirror
      Removal and installation of glass of a mirror
      Removal and installation of a trunk lid
      Removal and installation of facing of a trunk lid
      Removal and installation of a clamp of the lock of a luggage carrier
      Removal and installation of the lock of a door of a back
      Removal and installation of the mechanism of the lock of a door of a back
      Removal and installation of the cylinder of the lock of a luggage carrier and door of a back
      Removal and installation of a door of a back
      Adjustment of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of a back spoiler
      Removal and installation of a cap of a cargo compartment
   + Equipment of salon
+ Onboard electric equipment












Removal and installation of the lever of a back screen wiper

Versatile person

Removal

 PERFORMANCE ORDER

1. Moisten back glass with water.
2. Start for a short time a screen wiper and stop it the switch. Thus the cleaner comes to extreme situation.
3. Mark the provision of a brush at correctly adjusted levers on glass, for example, with an adhesive tape.

4. Cast away a cap (1) and turn off a nut (2).

5. Cast away the lever (3) and remove it.

 At the same time do not damage the jet inserted into a cleaner axis.


Installation

 PERFORMANCE ORDER

1. Make sure that the electric motor of a screen wiper is in extreme situation. If necessary start the electric motor for a short time and stop the switch.
2. Install the screen wiper lever on an axis and expose on the mark put with an adhesive tape at removal.
3. Screw a nut (2).
4. Double-check extreme position of levers. For this purpose close a cowl, moisten glass with water and for a short time start a screen wiper. Levers have to return to the established situation and should not go beyond glass at purification of glass.
5. If necessary once again turn off nuts and repeat adjustment.
6. Fix a nut (2) by the moment of 12 Nanometers and put on a cap.