Mercedes C-Class

W203 since 2000 of release

Repair and operation of the car



Mercedes-Benz
+ Mercedes-Benz cars of class C (W-203)
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
- Body
   - Leaving and external equipment of a body
      General information and security measures when carrying out body works
      Cleaning and leaving
      Repair of insignificant damages of body panels
      Repair of considerable damages of a body
      Damages of a windshield as a result of hit of stones
      Replacement of brushes of screen wipers
      Removal and installation of a jet of windscreen washer of a windshield
      Removal and installation of a jet of back glass
      Removal and installation of the lever of a screen wiper of a windshield
      Removal and installation of the lever of a back screen wiper
      Removal and installation of a catchment basin
      Removal and installation of a cowl
      Removal and installation of facing of a cowl
      Adjustment of a cowl
      Removal and installation of the lock of a cowl
      Drive cable detachment from the cowl lock
      Removal and installation of a lattice of a spoiler
      Removal and installation of a bumper
      Removal and installation of a rear bumper
      Removal and installation of a forward wing
      Removal and installation of a protective level on a wing
      Removal and installation of a protective level on a bumper
      Removal and installation of a protective level on a door
      Removal and installation of a forward loker covered
      Removal and installation of a back part of a loker of a wing
      Removal and installation of a forward door
      Adjustment of a door
      Removal and installation of forward facing of a door
      Removal and installation of a triangular slip
      Removal and installation of the external handle of a door
      Removal and installation of facing of an external rear-view mirror
      Removal and installation of an external mirror
      Removal and installation of glass of a mirror
      Removal and installation of a trunk lid
      Removal and installation of facing of a trunk lid
      Removal and installation of a clamp of the lock of a luggage carrier
      Removal and installation of the lock of a door of a back
      Removal and installation of the mechanism of the lock of a door of a back
      Removal and installation of the cylinder of the lock of a luggage carrier and door of a back
      Removal and installation of a door of a back
      Adjustment of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of facing of a door of a back
      Removal and installation of a back spoiler
      Removal and installation of a cap of a cargo compartment
   + Equipment of salon
+ Onboard electric equipment







Removal and installation of the external handle of a door

Removal

 PERFORMANCE ORDER

1. Disconnect a negative cable (-) of the rechargeable battery at the switched-off ignition. It is previously necessary to remove a box of the filter of air of salon.

 Before a detachment of a cable find out a protective code of the radio receiver if that is available, address the Section Replacement of the Rechargeable Battery.

2. Unlock a car door the ignition key. During the subsequent work keep a condition of a door unlocked.

3. Open a door and disconnect a sealing tape (1) at door handle height from a door frame.

4. Enter the screw-driver into an opening (2) and unscrew the small Torx screw.

5. Pull the handle of a door (1) and you keep it in this situation. At the same time take out the cylinder of the lock (2).

6. Disunite the socket (3) cylinders of the lock and remove the cylinder.

7. Uncover (1) the lock cylinder.

8. Pull the door handle back (an arrow on an illustration) and take out it from the forward holder.

9. Disconnect the handle from the back holder (2) and remove from a door.
10. Remove sealing laying for the door handle.


Installation

 PERFORMANCE ORDER

1. Install the door handle with sealing laying into place. Insert at first the handle in the back holder, at the same time the lever (3) has to enter gearing behind a lead (1) of the locking mechanism. (2) – lock cylinder.

On an illustration the basic collar (4) handles from the inside of a door is shown. For removal of a basic collar it is necessary to remove facing of a door.

2. Insert the handle in the forward holder, at the same time press the handle forward.
3. Pull the handle and you keep it in this situation and insert at the same time the lock cylinder with a cover.

If the condition of unlocking was broken, previously put the lock with an emergency key by turn counterclockwise in situation "openly".

4. Screw the Torx screw and fix the cylinder to a door.
5. Fix a sealing tape at a door frame.
6. Attach a negative cable (-) to the rechargeable battery at the switched-off ignition. Establish into place a box of the filter of air of salon. Enter a code of the radio receiver and determine time on hours.
7. Check operation of the mechanism of locking of a door.

At wrong blocking of the uniform lock if necessary return back settings of the control panel.